2018 Latest DCPPE-200 Exam Dumps, Valid DCPPE-200 Exam Braindumps, Accurate DCPPE-200 Study Guide, DCPPE-200 Exam Q&A, DCPPE-200 Learning Materials, DCPPE-200 Practice Questions

NEW QUESTION: 1
A VRTX server comes with two server modules. The customer requests to assign three PCle
Adapters per each server module. While performing this configuration, the engineer is unable to
assign more than two PCle Adapters per server module.
What is the cause of this issue?
A. The CMC configuration needs to be reset to the factory defaults.
B. This is a limitation of VRTX chassis.
C. The VRTX chassis needs to be updated with the latest firmware.
D. The VRTX chassis came with a CMC Express License.
Answer: B

NEW QUESTION: 2
A VRTX has the following physical disks:
-8 300 GB SSDs
-10 300 GB 15,000 rpm HDDs
An engineer needs to create two virtual disks for a file server: a system volume and a data volume.
The customer wants to maximize performance of the system volume and maximize redundancy of
the data volume.
The customer also wants both virtual disks to survive one drive failure without the customer's
intervention.
Which option is most appropriate to meet the requirements?
A. System: 7 SSDs in RAID 0Data: 9 HDDs in RAID 6One SSD and one HDD as dedicated hot spares for
each volume
B. System: 7 SSDs in RAID 5Data: 9 HDDs in RAID 6One SSD and one HDD as dedicated hot spares for
each volume
C. System: 6 SSDs in RAID 10Data: 10 HDDs in RAID 6Two SSDs as dedicated hot spares for each
volume
D. System: 8 SSDs in RAID 10Data: 8 HDDs in RAID 6Two HDDs as dedicated hot spares for each
volume
Answer: B

Valid DCPPE-200

Dumps shared by freecram for Helping Passing DCPPE-200

Exam! freecram now offer the newest DCPPE-200 exam dumps, the freecram DCPPE-200 exam questions have been updated and answers have been corrected get the newest freecram DCPPE-200 dumps with Test Engine here:  http://www.freecram.com/Home/Search?q=DCPPE-200 (88 Q&As Dumps, 30%OFF Special Discount: 30free )

NEW QUESTION: 3
Refer to the exhibit.
Refer to the exhibit.
An engineer sets up FCoE boot on their server. The server fails during post.
What needs to be added to the NIC settings/option ROM to make booting successful?
A. The WWN of the fibre channel switch
B. The WWN of the FC port ID
C. The WWN of the FIP snooping bridge
D. The WWN of the storage target
Answer: B

NEW QUESTION: 4
An engineer needs to configure a full height blade server and iSCSI traffic. The blade has two
dual port NDCs. The M1000e chassis only has switches in A fabric.
A1 - Production traffic:
174.1.0.0/16 network
Server facing switch ports use tagged VLANs 10, 30, 50
A2 - iSCSI traffic:
10.0.0.0/24 network
Untagged traffic
Switch is set to access VLAN 20
The engineer needs to set up the host to operate on the iSCSI network using two ports.
Which ports should be used?
A. Use NIC port 2 and 4 together for iSCSI
B. Use NIC port 3 and 4 together for iSCSI
C. Use NIC port 1 and 4 together for iSCSI
D. Use NIC port 1 and 3 together for iSCSI
Answer: A

NEW QUESTION: 5
A new node is added to a VRTX to create a compute cluster. This node needs to access the
same virtual disk as an existing node in the VRTX.
Which two settings need to be modified to allow the node access? (Choose two.)
A. Assign the virtual disk Full Access on the new node
B. Modify controller settings to SharedMode
C. Map the same virtual adapter to both nodes
D. Change the virtual adapter to Multiple Assignment
Answer: B,D